Budget Studio Monitor Isolation Stands


As I’ve been finishing up the final components of my personal studio I started looking at my studio monitor floor stands. With how I have the studio currently arranged I literally backed myself into two corners. I just can’t put the monitors where they need to be using the floor stands… slightly in line with the computer displays and pointed in towards the center seating position. My desk is just huge and it leaves no room on the sides or even behind to get proper placement.

I compared a few different solutions and came away with a few standard ways studio monitors are deployed. Of those there are some pros and cons to each method. Mostly they all lead to a discussion about isolation which is simply a fancy way of stating that you want to reduce the influence the monitors have on every solid surface they touch. This reduces vibration transfer and provides the cleanest sound possible from your speakers.

The most common monitor placement methods are as follows:

Wall Mounts

These are usually limited to specific manufacturers and models where compatible mount kits are available. As the name suggests… you bolt the stand to the wall and the monitor to the stand. The solution is somewhat permanent as you only end up with minor adjustment methods. As far as isolation is concerned the only point of vibration transfer is the mounting rod between the monitor and wall. With an interior wall of less density this can create some low frequency oddities.

Studio Desks

Many commercial studio desks (from entry level all the way to commercial desks with a meter bridge) have at-height shelving to accommodate one or more studio monitors. Slap the monitors on the desks and you’re ready to go. The fallback to these solutions is that the monitors are placed directly on the desk surface which causes two specific issues. The first potential issue is vibration transfer to the entire body of the desk. The second issue is sound reflection. Depending on the design of the speakers and placement on the stand the sound waves can find an immediate spot to throw early reflections of the sound waves. In my case I do not have a multi-tier desk so this isn’t an option for me.

Floor/Desk Stands

Floor stands offer many great benefits. Properly constructed they have nearly no contact with a source of vibration short of the stand itself and can be placed above and away from any desk avoiding immediate reflection issues. There is some bass transfer into the stand itself and may only be of concern if the stand is hollow and/or the floor is not very rigid or has a large air gap between floors, etc.

When it comes to after-the-fact isolation of speakers in these deployments the focus is most often on studio desks more than floor stands but both are solved by isolation which comes in two flavors: absorption and minimizing contact. Some solutions combine both techniques.


The primary material of choice used for absorbing the vibrations caused by studio monitors and reducing the vibration transfer to the studio desk or stand surface is quite simply foam. There are a few different commercially available solutions out there but essentially there is a block or wedge of slightly denser acoustic foam placed between the monitors and base.

Minimizing Contact

The second method for reducing vibration is to reduce the total amount of contact shared between the monitor and the desk or stand. This is often handled by a matrix of vertical cones or pipes (usually covered in a rubber material) that reduce the total surface area on which the monitor rests.

Think of your car on four tires. There is a very low amount of surface area shared between your car and the road, In many cases the minimized contact of monitors is augmented by a way to ‘float’ the points of contact through a dampening material as well. So again… just like your car makes minimal contact with the road through the rubber and air-filled tires, the ride is smoother and quieter when shock absorbers are added to the mix.

After comparing all the solutions I decided the IsoAcoustics solutions looks the most promising but considering all the other expenses of putting my studio in order (along with Christmas, children, etc, etc) I can’t help but go DIY and see what I can do to get a good compromise for minimal cash.

Off we go…

The IsoAcoustics Design


I have to admit I love the way these puppies look and I know I’m not going to get an exact technical match. The point of this build is to get good isolation on the cheap. The IsoAcoustics design appears to essentially surround the posts in shock absorbing rubber, use a cupped seating point to contact the monitor, and utilize rubber feet to isolate the stand from the desk. My goals for the build are similar:

  • Minimize contact between the monitors and stands
  • Minimize contact between the stands and the desk
  • Apply some form of dampening inside the stand frame
  • Apply some form of absorption at the contact points

The Materials


I purchased 100% of the build materials for this project from my local home improvement center and here is the shopping list:

  • 4 x Five Foot ½” PVC Pipes
  • 16 x ½” PVC Side Outlets (90 degree corners with a vertical couple)
  • 8 x 2 pack 1 inch Auto Body panel plugs
  • 1 Pack of 16 furniture gripper pads
  • 16 5/8” wire grommets
  • 1 Can of spray foam insulation
  • 1 Can spray paint

Materials ran me around $40.00 total with $7.00 sucked up in spray foam and paint. Not counting paint and foam cure time each stand takes about 15-20 minutes to assemble.

The Build

We start by determining the height of our monitors on the desk. I wanted a full ten inches of clearance between the desk top and monitor.

Cut 8 PVC pipes to a length taking into account the length of the coupler minus the internal flange and the 1/2 on each end for the rubber feet and spacers. Next determine the width and depth of the stand frame to determine how many of the 16 (if width and depth match) or 8 and 8 (if width and depth differ) horizontal bars to cut from the remaining PVC stock. I decided to go square and ended up with 16 bars when coupled measured a total of 8 ¼ inches.


Cut all PVC lengths as required. Make sure the lengths are absolutely as close as possible to each other in length to reduce the chances of the stands being crooked. If you have a pipe cutter you are golden, if you have a miter box you’re fantastic, if you just have a saw, take your time and measure/cut carefully. Using a utility knife or sandpaper remove all burring from the cut ends.


Now take a box, place the end of each pipe in it, and shoot the pipe full of the insulation foam. The box is just to catch any foam that might shoot out at first blast. If any gets on the outside edge (not the end) now might be a good time to wipe it off with a rag just to save some cleanup later on.


Set aside all pipes to dry and cure per the instructions. Clean the nozzle immediately… you are going to need it again soon.


While the pipes are curing use a punch or nail and place a starting divot in the center of the round mark on each PVC coupler.


Now use a small drill bit to ensure a good pilot hole…


Then use a 5/16” drill bit and drill a hole in each coupler at the divot.

Using a utility knife cut any foam that has expanded out of the pipes. Ensure the pipe face is cleaned of all remaining residue. It may be easiest after cutting to just rub the facing down with some sandpaper.


Now assemble the stands keeping the drilled openings on the top and bottom of the vertical limits of the stand. Use a level surface and a level on the stands to ensure everything is even. Use a rubber mallet or tap a piece of wood on top of the coupler with a hammer to ensure the pipes are fully mated to the couplers. You can choose to PVC glue the stands together but considering the short runs and amount of weight on the stands I think this would be overkill.


Now inject each hole with the spray foam insulation and wait again for the foam to cure. Wipe any excess away immediately to keep the finish smooth for painting. After the foam has cured cut away any excess that may have continued to ooze out with a razor or utility knife.


If you plan to paint the stand, do so at this time with your color of choice and give it plenty of time to cure so you don’t mar the finish in the final steps.


Using a nail or awl punch an inch into the foam through each coupling hole. The point here is simply to provide a large enough pilot hole for the body mounts that is also small enough so the ‘teeth’ on the mounts have something additional to grab onto.


Now place a rubber washer or grommet on each body mount then peel the adhesive from a gripper pad and place it on the flat face of the body mount.


Push each mount into the coupler mounting hole until the washer/grommet is touching both the mount and coupler. That’s it. You are done.


Here we have the near-final view of our stands.


And now the final view in their new home.

The Construction Theory

Basically the idea behind this build was to use a lightweight yet easy to manipulate and assemble material for this project. PVC was chosen but I wanted to avoid any resonance issues with the hollow tubing so I filled the tubing with insulating foam which would dampen the chambers while not adding too much rigidity.


In addition, I didn’t want to simply build a PVC cube and provide larger contact surfaces so using the body mounts provided some additional isolation while the rubber grommets reduced contact vibration with the frame and grippers reduced contact vibration from the monitors.

The Final Verdict

I am happy with the result and it’s a bonus to have the monitors where I so desperately wanted them placed. I can also tell the isolation does work. If they are as good as a commercial solution I cannot say but I am certain they are better than simply placing them on the desk, or on a box, etc. There is definitely a difference in bass response when I compare mixes with the speakers direct on the desk vs using the isolators.

So there you have it… go forth and isolate!

Multi-Option Dunlop GCB-95 Modification

This is a writeup on the extensive modifications I have made to my GCB-95 in order to provide a wide variety of sounds beyond the stock pedal.

While I heavily utilize IK Multimedia’s AmpliTube for my guitar rig there are times where I want to use outboard gear as well. After completing my Amplitube MIDI Controller I was literally left with a shell of a Dunlop Cry Baby GCB-95 pedal. I used the gear mechanism from the pedal to prototype the mechanics of my MIDI board then ended up stealing the bypass switch for a power button on a clean amp project.

After a few other projects this (aside from the circuit board and potentiometer not pictured) was all that was left:

When I started this project the intent was simply to get the OEM replacement parts and put the pedal back to stock shipping operations. As I looked at the replacement parts it started to become apparent that the existing circuit board could accept alterations such as replacement inductors and after some more digging online I found countless circuit board modifications to the GCB-95. Most all of the mods appeared to be one-way where the only way to ‘roll back’ to the original stock features was to replace all the parts. In addition, I didn’t see too many people trying to increase options for the inductors so I ultimately decided to combine many of the upgrades into one pedal. I had three primary goals for this project:

  •     I wanted the ability to switch between stock and mod settings
  •     All components needed to fit in the pedal casing
  •     The battery compartment could not be used for additional component storage

It took a few days but I was able to take on the project one phase at a time and ultimately get exactly what I was looking for. As always keep in mind that I am not a road-warrior musician so my projects have silly characteristics like switches sticking out of the side of a pedal that could easily be sheared right off by overzealous stage antics. Before I jump into the how-to I’ll go ahead and give you a look at the final product with a description of the features.

Left side of the pedal with a simple toggle to switch the voicing of the wah sweep. This basically toggles between the stock capacitor and a replacement for a more defined lower to midrange sweep.

Right side of the pedal with three toggles for midrange boost, gain boost, and vocal shaping. The three way switch near the heel provides access to the stock inductor, yellow vintage Fasel, and modern red Fasel inductors.

Two more notes before we dig in. The decision to include an inductor switch was made later on in the build after alot of the circuitry had already been reinstalled. You may want to do all the casing modifications first but if not, be aware you could end up with aluminum dust or shavings in the circuitry. Simply shop-vac or compressed air blast the casing clean in either case to avoid any shorting out of the circuitry. Additionally this mod does NOT send any of the signal to a buffering resistor on switching of the added features so it will most definitely ‘pop’ on switching as the capacitor discharges. You’ll want to throw the pedal into bypass or put down a volume/mute switch on the amp side of the pedal before toggling options… especially if you’re on a live and fully loaded amp.

If you just want to know the changes made, here is the baseline schematic:

Start by removing the wiring harness at top, 1/4 inch jack screws on the outside body, and mounting screw on the lower right of the board. Then remove the board and de-solder each of the following components from the stock circuit board.

L1 – The stock inductor. Save this component. IMPORTANT! … mark the component in some manner which helps you recall the position BEFORE you remove it. For instance you cannot see it here but I put mark on the side of the inductor near the area of the board that has L1 printed on it. This told me where the bottom right corner of the inductor should go. This will help you know how to correctly wire the inductor later.
R5 – Resistor controlling vocal shaping. Toss this.
R1 – Resistor controlling midrange. Toss this.
R9 – Resister controlling gain. Toss this.
C5 – Capacitor controlling the ‘sweep’ of the wah sound. Toss this.

This leaves us with a clean board:

Next we’ll work on the casing a little to hold 4 DPDT (Double Pole, Double Throw) miniature toggle switches.

The smaller the better when it comes to these switches because there isn’t alot of space in the casing.

The right side of the pedal is best for multiple switches given that when the potentiometer is placed in the housing there isn’t too much clearance on the left side. You’ll want to be ultra aware of the switch body size and proximity to the 1/4 jack mount flange (shown left) and rubber foot mount (shown right). Aesthetically your best bet is to mark the mounting position of those two holes first, then simply split the distance between them for the middle switch. The pedal base is cast aluminum which is very easy to drill. I recommend using a punch to set the center for drilling and starting with a smaller pilot hole to ensure the larger bit doesn’t travel when you start drilling the final mounting holes. For the sweep capacitor switch on the left side, simply match the position of the hole closest to the 1/4 inch jack to keep clear of the potentiometer base.

Outside shot of the housing showing the mounting holes running parallel with the top of the pedal base.

A quick fit-test to ensure the switches are not going to give us any issues.

Note the ample clearance between the circuit board and how the switch leads are just inside of the cut out area (rounded rectangle) for the gear assembly. Smaller switches that stay inside that area won’t interfere with the potentiometer.

Now remove each switch. Solder 2 leads about 6 inches long to the center terminals on each switch then getting the leads on the resistors and capacitors as close to the external terminals on the switch as possible, create the following switch combinations:

  • Switch One (Midrange): 2 six inch center leads with a 2.2kOhm (R-R-R-Gold) resistor across the terminals on one side of the switch and a 1.5kOhm (B-G-R-Gold) resistor across the opposite terminals of the switch.
  • Switch Two (Vocal Shaping): 2 six inch center leads with a 47kOhm (Y-V-O-Gold) resistor across the terminals on one side of the switch and a 33kOhm (O-O-O-Gold) resistor across the opposite terminals of the switch.
  • Switch Three (Gain): 2 six inch center leads with a 270Ohm (R-V-B-Gold) resistor across the terminals on one side of the switch and a 390Ohm (O-W-B-Gold) resistor across the opposite terminals of the switch.
  • Switch Four (Sweep): 2 six inch center leads with a 0.01uF capacitor across the terminals on one side of the switch and a 0.022uF capacitor across the opposite terminals of the switch.

Remember to mount the components as close as humanly possible to the terminals (note the image above) because you need to ensure they will not make contact with the mechanical components on the gear side of the potentiometer or the leads on the opposite side.

Now remount the toggle switches in the case and shape the leads to run as close to the casing walls as possible before falling between the 1/4 inch jacks and inductor space. I should point out here that I didn’t pay too much attention to the placement of the toggles with respect to the original resistor and capacitor values. It would probably be a good idea to put them all either towards the toe end or heel end of the pedal so when all switches point in the same direction you know you have reverted the pedal to ‘stock’ mode.

Cut another pair of 8 inch leads. Trim all toggle leads to as short a length as practical to keep wiring runs as short as you can and hook up the toggle leads and spare 8 inch leads as follows:

  • Switch One (Midrange): Solder leads to R1
  • Switch Two (Vocal Shaping): Solder leads to R5
  • Switch Three (Gain): Solder leads to R9
  • Switch Four (Sweep): Solder leads to C5
  • 8 Inch Leads: Referencing the image above solder the leads to the two holes on the left inside the inductor outline. Basically look to the right of R5 and connect to the two leads inside the larger circle but just to the left of the larger drilled hole in center of that circle. Leave the opposite ends loose for the time being.

Now remount the board to the casing with the single screw to the lower right.

Now it’s time to mount the inductors. Above you’ll see the stock black inductor and the aftermarket red and yellow Fasel inductors. It took me a little time to figure out how to jam these things in the pedal along with that massive switch but here is what I ultimately ended up doing.

The heel of the casing is practically the only place that all three inductors and an additional switch can be placed. After staring at this void for awhile I realized that just below that battery foam is a totally unused screw mount. This image was taken right after that discovery because there was also a much longer screw protruding from the nut just to the right of that mount point. Take a pair of pliers, grab that screw end and give it a couple of to and from tweaks. It will snap off right at the nut base.

Now find yourself some sort of non-conductive material and cut it to cover a majority of the void in the heel of the casing. In this case I used a semi thick sheet of plastic from some kind of binder. Those lightweight 1/2 inch vinyl binders with snap rings come to mind. The key is to just find something that a sharp wire or component lead will not easily puncture.

Next you are going to need a really short 6-32 screw… the same length as the one that holds the circuit board in place. If you can’t find one short enough just run a nut onto a 3/4 or longer 6-32 screw then using a hacksaw or bolt cutters, lop off the additional length. Running the nut back off of the screw will re-cut any damaged threading, making it easy to use the screw on the mounting hole.

Now find yourself a 1 3/4 inch square circuit board (set with copper solder points on the opposing side will help) and test fit the board using the mounting screw. This particular board came from Radio Shack and just happens to be a perfect fit all around… with the exception of that top notch which I will now explain.

As mentioned in the start of this post one of my requirements was to ensure I didn’t intrude on the existing pedal functionality… that included the battery compartment. The Dunlop Wah has this funky clip on the battery compartment that ends up taking up some real estate and just happens to run right along the line of that mounting screw. So using some nibblers and a file, I removed enough material to ensure the battery clip would still fit as expected.

You don’t need much clearance here… just enough to prevent the battery clip from pushing down the newly mounted circuit board.

And here is where things got tricky. You see the black inductor? It’s ever so slightly too tall to clear the bottom of the pedal… it sticks out if you look from the side so the bottom plate cannot be put on the pedal. If you look on the OEM circuit board between the 1/4 inch jacks you’ll see that there is a big hole drilled in the board.

The OEM inductor has a flange at the bottom. You’ll need to drill the circuit board to allow this flange to slide into the board. It will help get the clearance you need. Now for the next problem. The Fasel inductors mount vertically taking up even more room than the OEM inductor.

Using a pair of needle nose pliers gently (and I do mean GENTLY) bend the terminals right at the edge to move them into a 90 degree position. Do this for both the read and yellow Fasel inductors. You need to be super careful here because if you snap off the terminal you’re done and if you look on the opposite side of the plastic mount you’ll see just how thin and fragile the inductor wire really is.

If you did it right, the Fasel should now mount horizontally on the circuit board.

Temporarily Solder the inductors in the following configuration, keeping the OEM aligned the same as before. Remember I marked the lower right corner earlier which means I mounted this with the lower right corner mark towards the bottom right of the heel and picture in this photo. Now we move on to the switch. Notice from the previous picture how long the terminals are on the switch? Notice how close the lower mounting hole is to the rubber foot mount? This is going to be tight. Start by using wire cutters and trim off to the top half of the switch terminals. If you notice you’ll see additional mounting holes close to the body that we can use. We need that real estate or the battery will either not fit, or will shor the contacts on the switch.

Measure the height of the switch using a ruler or caliper.

Now pick a drill bit just slightly larger than that.

This step is a little tricky as you have to look at the inside and outside of the casing to get it just right but place the switch in the leftmost throw and set it on the body where if you were to drill through and place a nut on the backside, it would not interfere with that mounting post. The Dunlop is painted with powder coat so it’s easy to scratch. Scratch a mark at the outside edge of the switch then carefully move the slider to the far opposite throw point and make a mark on that outside edge as well.

I got a little carried away here but scratch a line parallel to the top of the pedal body then punch three holes at points where the drill bit will meet the left top, top, and top right edges of the mark from a dead center drill on the punch marks.

Drill pilot holes first with a 1/8 inch or smaller bit. This will help keep the larger bit from traveling too far on the final sizing run. After the pilot holes have been drilled, switch to your selected bit and open up the slot by drilling into each pilot hole.

You’ll need to use a smaller file at first to knock out the ‘points’ between the holes.

Once you have gained enough space, a larger file will fit and definitely speed up the job. Check your work often with both the caliper/ruler and actual switch to ensure there is clearance for the throw on all sides.

Once you are happy with the clearance place the switch on the outside of the body with the slider pointing in. Hold firmly while ensuring the slider moves effortlessly down the channel then make to registration marks in the mounting holes and drill for the mounting screws.

As you can see the final mounted switch with trimmed terminals and short screws/nuts will keep clear of the 9volt ‘zone’

Wire all inductors as indicated in this schematic:

The completed mod. Note the black wire ties used on the inductors just to help add stability and wire ties across all added wiring to keep things clear.

Everything works great so far. As mentioned earlier this mod does NOT send any of the signal to a buffering resistor on switching of the added features so it will most definitely ‘pop’ on switching as the capacitor discharges. You’ll want to throw the pedal into bypass or put down a volume/mute switch on the amp side of the of the pedal before toggling options… especially if you’re on a live and fully loaded amp.

In an upcoming post I’ll show the features of the mods with some sound samples, etc.

New Pedalboard Underway

It’s been awhile since I posted and even longer since my first pedalboard project. Well… the first extension to my project is officially underway. This will be an add on to the original board providing me with around 32 new switches for triggering and 4 new controllers. In the background you might spot a Dunlop wah also getting some new guts as part of the rig upgrade.  Stay tuned…


Pedalboard Kick Test

I was asked if there were any videos of the pedalboard in use. At the moment all I have is this older video of me noodling around with the system. The sound is from a room mic on the camera so it’s not the best quality but the video shows interaction between the board and DAW/VST.

Life, Projects, and Randomized Music

Since I finished up the initial pedalboard design my world has flipped, flopped, and spun in too many directions to count. A few short weeks ago my wife and I discovered we have a little one on the way. So all immediate plans to start recording have been put on hold while I prepare the house for this exciting little addition. One nice side benefit to this is that I get to move the studio (again). I always meet this task with a certain level of excitement and dread. It’s great to have a new space, but that always brings weeks of tweaks and room arranging. Hopefully this will be the last move for awhile.

On the project front I’ve started plans for two new boards which will augment my guitar rig. I don’t want to get into the details of one because it is just a little too awesome and ear-popping to give away in words alone… so more to come there. The second of these new boards is pretty simple. I’ve been playing around with Mobius and live looping with Albeton Lite. It’s quite a different animal than studio recording but I’m having some fun so far. I’ll be building a special controller for Mobius based on what feels right once I get more familiar with the system.

Now on to Conjure… my other pet project. I’ve briefly talked about this with a few people on Facebook but the Conjure project is a music composition system I’ve been working on since about Feb of 2010 but is finally getting close to a useful beta. It’s a rather complicated long-term development project but essentially Conjure is a preference engine for producing MusicXML scores. The idea is that given enough information about music theory with a combination of personal music preferences the system can create root song structures. The intent here isn’t to create complete scores as much as serving as a virtual muse. Going through the system has given me a great opportunity to relearn alot of music theory knowledge that’s been lost over the years. At this point Conjure has awareness of about 85 scales and some 60 odd chord structures and how they relate to all the standard western music keys. There is a title generation system, ensemble assembly function, GM MIDI database, drumkit constructor… and hordes of other tables cobbled together for one reason or another. Development has primary settled in with ColdFusion as the web services provider and a mix of XSL/XML/DHTML and possibly Flex for an alternative interface. The past two weeks have been consumed with providing Conjure information about song structures while I’ve just recently started refining the music key/scale selection criteria to introduce harmony and chord progressions (which will then be coupled with the structures.)

Here is an early twiddling from Conjure months ago when it was locked down to a single key but allowed to roam freely among orchestra instruments from IK Multimedia’s Miroslav Philharmonik VST plug in.

Quick Guide To Using External MIDI Controllers with AmpliTube 3

The release of AmpliTube 3 added a host of new features for interactive control of effect settings via external controllers. Among the options for control via IK Multimedia’s StealthPedal and upcoming StealthBoard you’ll find an option for controlling AmpliTube 3 via MIDI. There are a few layers to the control options such as parameters and patches but in this post I’m going to focus on the quick-and-dirty “I have this pedal and want to make it work” approach. While this post focuses on the standalone implementation of AmpliTube 3, there isn’t much difference when using your DAW. For your DAW just setup a MIDI input and route the signal to the instance of AmpliTube 3 you wish to control.

So if you’ve never seen AmpliTube, crawl out from under your rock and take a peek.

Amplitube 3
Amplitube 3

Pop into the device setup (for standalone instances) and setup your interface and MIDI device parameters.

AmpliTube Settings Screen
AmpliTube Settings Screen

Now flip over to the STOMP A section of the signal chain and let’s drop a Wah 46 on the floor.

Wah 46 (my fav)
Wah 46 (my fav)

IK Multimedia couldn’t have made the MIDI setup for this any easier or more straightforward. Simply right mouse click the aspect of the effect you wish to alter to reveal the Assign Midi -> Learn function.

The Learn Function
The Learn Function

AmpliTube will now enter the Learn mode waiting for you to engage your physical pedal that you want to use to control the effect.

MIDI Learn Waiting For Your Input
MIDI Learn Waiting For Your Input

Now for the hard part… drag your lazy foot off the floor and push the pedal you want to use. The interface will dismiss the Learn message and you should be controlling the pedal. Good times!

Now let’s try a pushbutton because there are a few ways those little gizmos work within the interface.

Right mouse click the mode (off, on , auto) above the wah. You might notice there is no ‘bypass’ option. This is one thing I don’t completely understand about the way IK implemented the MIDI Learn functionality. I personally would like to also see the bypass option available for any pedal that has a multi-mode like this, but that’s just a personal tic. Not a huge deal because IK has given us more than one way to assign control. In the lower right area of AmpliTube click the MIDI button.

MIDI Button
MIDI Button

The MIDI settings screen will appear. In this area you will already see the Wah MIDI control we setup. Now we’re going to manually configure a controller.

MIDI Window
MIDI Window

Click the Add button at the bottom of the window and a menu will appear. Navigate into the Stomp A signal chain -> Wah 46 then select Bypass. A new row will be added to the parameters list.

Adding A Parameter To Control
Adding A Parameter To Control

Now with the new row selected, click the Learn button and AmpliTube will enter the MIDI Learn mode.

Waiting For Button Input
Waiting For Button Input

Press your ‘real world’ button and AmpliTube should change the CC# to match the message sent by your controller button.

There may be one more step depending on your physical pedal construction. If your pedal snaps/latches like an on/off switch then the Latch Mode off would be preferred (and is the default) however if your switch is momentary then pressing your button would enable the pedal while letting the switch go would disable it. To alter this behavior simply click the word OFF in the parameter row to change it to ON and all is well.

Altering Latch Mode
Altering Latch Mode

So there you have it… two ways to get immediate satisfaction in AmpliTube 3 with your external MIDI controller.

Lather, Rinse, Repeat.

Pedalboard Functions

Here’s a quick breakdown of the pedalboard functionality:

Pedalboard Controls
Pedalboard Controls

Analog Functionality

  • 1/4 inch input
  • 1/4 inch TRS insert
  • 1/4 inch output
  • SPDT switch for selecting to enable the insert or not
  • SPDT switch for defeating the input
  • SPST momentary switch for temporarily stopping input until switch is released
  • Audio taper potentiometer for volume pedal

Issues – I don’t know alot about passive analog circuitry but now know there is a huge difference in the selection of the potentiometer rating for the volume control. It’s currently a 10K pot when it should be a 250K instead… which is closer to what’s actually inside a guitar to begin with. An incorrect selection here degrades the power of the signal.

Potential Fix – Just replace the pot but I also like the degraded effect and will find a way to mimic the circuit path even with the new pot in place.


MIDI Functionality

  • 2 SPST Momentary switches intended for patch changes
  • 6 SPST Momentary switches intended for bypass/defeat of the MIDI pedals
  • 6 10K linear potentiometers for the MIDI pedals
  • 1 Pitch bend/MOD wheel from a discarded Roland Keyboard controller
  • 1 SPST Momentary switch for MIDI Panic/Reset

Issues – The only issue is the pitch bend wheel. It doesn’t allow for a full throw (not a physical limitation) and as such won’t transmit the full 0-127 MIDI data range. I can only assume the wheel had accessory circuitry to translate this properly.

Potential Fix – At some point I’m going to have to pull apart the wheel assembly and see if I can replace the potentiometer to the proper spec.



  • 5 Pin MIDI In/Out
  • 7-12V / 100mA DC Input
  • SPDT switch for power enable/defeat
  • LED for MIDI activity

Issues – None